air filter YAMAHA TTR110 2008 Owners Manual

TABLE OF CONTENTSSAFETY INFORMATION ..................1-1
Safe riding ......................................1-1
Location of important labels ............1-4
DESCRIPTION ..................................2-1
Left view ..........................................2-1
Right view ........................................2-2
Controls and instruments.................2-3
INSTRUMENT AND CONTROL
FUNCTIONS.......................................3-1
Main switch .....................................3-1
Handlebar switches ........................3-1
Shift pedal .......................................3-2
Brake lever .....................................3-2
Brake pedal ....................................3-2
Fuel tank cap ..................................3-3
Fuel .................................................3-3
Fuel tank breather hose ..................3-4
Fuel cock ........................................3-5
Starter (choke) lever .......................3-6
Kickstarter .......................................3-6
Seat ................................................3-6
Sidestand ........................................3-7
Starting circuit cut-off system .........3-7
PRE-OPERATION CHECKS..............4-1
Pre-operation check list ..................4-2OPERATION AND IMPORTANT
RIDING POINTS................................. 5-1
Starting and warming up a cold
engine ......................................... 5-1
Starting a warm engine .................. 5-2
Shifting ........................................... 5-2
Engine break-in .............................. 5-3
Parking ........................................... 5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR................................. 6-1
PERIODIC MAINTENANCE ........... 6-1
Owner’s tool kit ............................... 6-2
Periodic maintenance chart for
the emission control system ....... 6-3
General maintenance and
lubrication chart .......................... 6-4
Removing and installing panels ..... 6-6
Checking the spark plug ................. 6-7
Engine oil ....................................... 6-8
Cleaning the air filter element ...... 6-10
Cleaning the spark arrester .......... 6-12
Adjusting the carburetor ............... 6-13
Adjusting the engine idling
speed ........................................ 6-13
Checking the throttle cable free
play ........................................... 6-14
Valve clearance ............................ 6-14
Tires ............................................. 6-15
Spoke wheels ............................... 6-16Accessories and replacement
parts ......................................... 6-16
Adjusting the clutch free play ....... 6-17
Adjusting the brake lever free
play ........................................... 6-17
Adjusting the brake pedal free
play ........................................... 6-18
Checking the shift pedal .............. 6-19
Checking the front and rear brake
shoes ........................................ 6-19
Drive chain slack .......................... 6-20
Cleaning and lubricating the
drive chain ................................ 6-21
Checking and lubricating the
cables ....................................... 6-22
Checking and lubricating the
throttle grip and cable ............... 6-22
Checking and lubricating the
brake lever ................................ 6-23
Checking and lubricating the
brake pedal ............................... 6-23
Checking and lubricating the
sidestand .................................. 6-23
Lubricating the swingarm
pivots ........................................ 6-24
Checking the front fork ................. 6-24
Checking the steering .................. 6-25
Checking the wheel bearings ....... 6-25
Battery ......................................... 6-26
Replacing the fuse ....................... 6-27
Supporting the motorcycle ........... 6-28U5B680E0.book Page 1 Tuesday, July 17, 2007 9:11 AM

DESCRIPTION
2-2
2
EAU10420
Right view
12 3 4
857
6
1. Spark arrester (page 6-12)
2. Seat (page 3-6)
3. Fuel tank (page 3-3)
4. Air filter element (page 6-10)
5. Spark plug cap (page 6-7)
6. Engine oil filler cap (page 6-8)
7. Brake pedal (page 3-2)
8. Kickstarter (page 3-6)U5B680E0.book Page 2 Tuesday, July 17, 2007 9:11 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
6
EAU39943
Periodic maintenance chart for the emission control system NOTE:

From 7000 km (4200 mi) or 18 months, repeat the maintenance intervals starting from 3000 km (1800 mi) or 6 months.


Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technicalskills.
No. ITEM CHECKS AND MAINTENANCE JOBSINITIAL ODOMETER READINGS
1000 km
(600 mi) or
1 month or
30 hours3000 km
(1800 mi) or
6 months or
90 hours5000 km
(3000 mi) or
12 months or
150 hours
1*Fuel lineCheck fuel hoses for cracks or damage.
Replace if necessary.√√
2 Spark plugCheck condition.
Adjust gap and clean.√√
3*Valve clearanceCheck and adjust valve clearance when engine is cold.√
4*Air filter elementClean with solvent.
Replace if necessary.√√
5*Crankcase breather sys-
temCheck ventilation hose for cracks or damage and drain
any deposits.
Replace if necessary.√√√
6*CarburetorCheck engine idling speed and starter operation.
Adjust if necessary.√√√
7 Exhaust systemCheck for leakage.
Tighten if necessary.
Replace gasket(s) if necessary.√√
8 Engine oilChange (warm engine before draining).√√√
U5B680E0.book Page 3 Tuesday, July 17, 2007 9:11 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
6
EAU40000
NOTE:The air filter needs more frequent service if you are riding in unusually wet or dusty areas.10*Chassis fastenersCheck all chassis fitting and fasteners.
Correct if necessary.√√√
11 Brake lever pivot shaftApply lithium-soap-based grease lightly.√√
12 Brake pedal pivot shaftApply lithium-soap-based grease lightly.√√
13 Sidestand pivotCheck operation.
Apply lithium-soap-based grease lightly.√√
14*Spark arresterClean.√
15*Front forkCheck operation and for oil leakage.
Replace if necessary.√√
16*Shock absorber assem-
blyCheck operation and for oil leakage.
Replace if necessary.√
17*Control cablesApply Yamaha chain and cable lube or engine oil 10W-30
thoroughly.√√√
18*Throttle grip housing and
cableCheck operation and free play.
Adjust the throttle cable free play if necessary.
Lubricate the throttle grip housing and cable.√√√ No. ITEM CHECKS AND MAINTENANCE JOBSINITIAL ODOMETER READINGS
1000 km
(600 mi) or
1 month or
30 hours3000 km
(1800 mi) or
6 months or
90 hours5000 km
(3000 mi) or
12 months or
150 hours
U5B680E0.book Page 5 Tuesday, July 17, 2007 9:11 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
67. Turn the engine off, and then
check the oil level and correct it if
necessary.
EAU41633
Cleaning the air filter element The air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more fre-
quently if you are riding in unusually
wet or dusty areas.
To clean the air filter element
1. Remove panel A. (See page 6-6.)
2. Remove the air filter case cover by
removing the screws.
3. Pull the sponge material and the
mesh out.4. Clean the mesh with solvent, and
then wipe the solvent off.
5. Clean the sponge material with
solvent, and then squeeze the re-
maining solvent out.
WARNING
EWA10430
Use only a dedicated parts cleaning
solvent. To avoid the risk of fire or
explosion, do not use gasoline orsolvents with a low flash point.CAUTION:
ECA10510
To avoid damaging the foam materi-
al, handle it gently and carefully, anddo not twist or wring it.
1. Air filter case cover
2. Screw
2 1
1. Sponge material
2. Air filter mesh
1
2
U5B680E0.book Page 10 Tuesday, July 17, 2007 9:11 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
6 6. Apply oil of the recommended type
to the entire surface of the sponge
material, and then squeeze the ex-
cess oil out.
NOTE:The sponge material should be wet butnot dripping.
7. Insert the mesh and the sponge
material into the air filter case.
CAUTION:
ECA15571


Make sure that the mesh and the
sponge material are properly
seated in the air filter case.


The engine should never be op-
erated without the mesh and the
sponge material installed, oth-
erwise the piston(s) and/or cyl-
inder(s) may becomeexcessively worn.
8. Install the air filter case cover by in-
stalling the screws.
NOTE:Make sure that the spark plug cable isrouted as shown.9. Install the panel.
To clean the air filter check hose
1. Check the hoses at the bottom of
the air filter case for accumulated
dirt or water.
Recommended oil:
Yamaha foam air filter oil or other
quality foam air filter oil
1. Spark plug cable
1. Air filter check hose
1 1
1
U5B680E0.book Page 11 Tuesday, July 17, 2007 9:11 AM

SPECIFICATIONS
8-1
8
Dimensions:Overall length:
1565 mm (61.6 in)
Overall width:
680 mm (26.8 in)
Overall height:
923 mm (36.3 in)
Seat height:
670 mm (26.4 in)
Wheelbase:
1080 mm (42.5 in)
Ground clearance:
180 mm (7.09 in)
Minimum turning radius:
1660 mm (65.4 in)Weight:With oil and fuel:
72.0 kg (159 lb)Engine:Engine type:
Air cooled 4-stroke, SOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
110.0 cm³
Bore × stroke:
51.0 × 54.0 mm (2.01 × 2.13 in)
Compression ratio:
9.30 :1
Starting system:
Electric starter and kickstarter
Lubrication system:
Wet sump
Engine oil:Type:
TT-R110E SAE10W-30, SAE10W-40,
SAE15W-40, SAE20W-40 or SAE20W-50
TT-R110EX SAE10W-30, SAE10W-40,
SAE15W-40, SAE20W-40 or SAE20W-50
(AUS)
TT-R110EX YAMALUBE 4, SAE10W-30 or
SAE20W-40 (CAN)Recommended engine oil grade:
API service SG type or higher, JASO
standard MA
Engine oil quantity:
Periodic oil change:
0.80 L (0.85 US qt) (0.70 Imp.qt)
Air filter:Air filter element:
Wet elementFuel:Recommended fuel:
TT-R110E Regular unleaded gasoline only
TT-R110EX Regular unleaded gasoline
only (CAN)
TT-R110EX Unleaded gasoline only (AUS)
Fuel tank capacity:
3.8 L (1.00 US gal) (0.84 Imp.gal)
Fuel reserve amount:
0.5 L (0.13 US gal) (0.11 Imp.gal)Carburetor:Manufacturer:
MIKUNI
Type × quantity:
VM16 x 1Spark plug (s):Manufacturer/model:
NGK/CR6HSA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)Clutch:Clutch type:
Wet, multiple-disc and centrifugal
automatic
-20 -10 0
10 20 30
40
50 ˚C
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50
10˚30˚50˚70˚90˚110˚
0˚
130
˚F
YAMALUBE 4 (10W-30)
or SAE 10W-30
YAMALUBE 4 (20W-40)
or SAE 20W-40
–10
˚0˚10˚20˚30˚40˚
–20˚
50 ˚C
U5B680E0.book Page 1 Tuesday, July 17, 2007 9:11 AM

INDEX
AAccessories and replacement parts ..... 6-16
Air filter element, cleaning .................... 6-10BBattery .................................................. 6-26
Brake lever ............................................. 3-2
Brake lever, checking and lubricating ... 6-23
Brake lever free play, adjusting ............ 6-17
Brake pedal ............................................ 3-2
Brake pedal, checking and
lubricating ........................................... 6-23
Brake pedal free play, adjusting ........... 6-18
Brake shoes, checking ......................... 6-19CCables, checking and lubricating .......... 6-22
Carburetor, adjusting ............................ 6-13
Care ........................................................ 7-1
Clutch free play, adjusting .................... 6-17DDrive chain, cleaning and lubricating .... 6-21
Drive chain slack .................................. 6-20EEngine break-in ...................................... 5-3
Engine idling speed .............................. 6-13
Engine oil ................................................ 6-8
Engine, starting a warm .......................... 5-2
Engine stop switch.................................. 3-1FFront fork, checking .............................. 6-24
Fuel......................................................... 3-3
Fuel cock ................................................ 3-5
Fuel tank breather hose.......................... 3-4
Fuel tank cap .......................................... 3-3
Fuse, replacing ..................................... 6-27
HHandlebar switches ................................. 3-1IIdentification numbers ............................. 9-1KKey identification number ........................ 9-1
Kickstarter ............................................... 3-6LLabels, location of ...................................1-4MMain switch ............................................. 3-1
Maintenance and lubrication, periodic..... 6-4
Maintenance, emission control system ... 6-3
Maintenance, periodic ............................. 6-1
Matte color, caution .................................7-1
Model label .............................................. 9-2PPanels, removing and installing .............. 6-6
Parking ....................................................5-4
Part locations .......................................... 2-1
Pre-operation check list........................... 4-2SSafety information ...................................1-1
Seat ......................................................... 3-6
Shifting ....................................................5-2
Shift pedal ............................................... 3-2
Shift pedal, checking ............................. 6-19
Sidestand ................................................ 3-7
Sidestand, checking and lubricating...... 6-23
Spark arrester, cleaning ........................ 6-12
Spark plug, checking ...............................6-7
Specifications .......................................... 8-1
Starter (choke) lever................................ 3-6Starting and warming up a cold
engine ................................................... 5-1
Starting circuit cut-off system.................. 3-7
Start switch ............................................. 3-1
Steering, checking ................................ 6-25
Storage ................................................... 7-3
Supporting the motorcycle .................... 6-28
Swingarm pivots, lubricating ................. 6-24
TThrottle cable free play, checking ......... 6-14
Throttle grip and cable, checking and
lubricating ........................................... 6-22
Tires ...................................................... 6-15
Tool kit .................................................... 6-2
Troubleshooting .................................... 6-31
Troubleshooting chart ........................... 6-32VValve clearance .................................... 6-14
Vehicle identification number .................. 9-1WWheel bearings, checking..................... 6-25
Wheel (front) ......................................... 6-28
Wheel (rear) .......................................... 6-30
Wheels .................................................. 6-16
U5B680E0.book Page 1 Tuesday, July 17, 2007 9:11 AM